Page 1 of 1

Tyrell 002 Francois Cevert.

Posted: Sun Feb 18, 2018 11:34 am
by Tay99
Hi all.
Going to try and get another car finished for the GB, this time it's the Tyrrell 002 by Ebbro, I've built the 003 before as driven by Jackie Stewart.
This one I will build as driven by Francois Cevert.
Here are the box and spur shots, paint for the bodywork and a little history about the car and team.

Image

Image

Image

Image

Image

The tyres come with logos already printed and 1970s tread.

Image

The kit comes with 2 body's 1 for Stewart's car and 1 for Cevert car the main difference is the wing mirror mounting points and side glass.

Image

Image

Image

Image

Image

Image

These are the tripods for the wing mirrors on the Jackie Stewart car

Image

Image

And here is the 003 I built, the main difference between the 2 cars is the nose and on the 002 car there is a airbox above the engine and also there are ribs on the rear wing of the 002.

Image

That's all for now thanks for looking.

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 18, 2018 12:00 pm
by exmoor
Looking great nice worklook forward to seeing the new build

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 18, 2018 1:19 pm
by Tay99
Here is some history about Francois his family and untimely death.


Image

The son of Charles Goldenberg (1901–1985), a Parisian jeweler, and Huguette Cevert. Charles was a Russian Jewish émigré brought to France as a young boy by his parents, to escape the persecution of the Jews under the Tsarist autocracy. During World War II, under the Nazi occupation of France, Goldenberg joined the French Resistance to avoid forced deportation to Poland, as he was a registered Jew. In order not to draw further attention, Charles and Huguette's four children were all registered with her surname rather than his. Some years after the liberation of France, Cevert's father wanted to rename his children Goldenberg, but the family objected as by now they had become known as Cevert.

Cevert was the brother-in-law of Grand Prix driver Jean-Pierre Beltoise.
Career

Early career
When he was 16, François Cevert began his motorsport career on two wheels, rather than four, initially racing his mother's Vespa scooter against friends, before graduating to his own Norton at the age of 19. After completing his National Service, Cevert switched his attention to cars. In 1966 he completed a training course at the Le Mans school, before enrolling at the Magny-Cours racing school. At the same time he registered for the Volant Shell scholarship competition, which offered the top finisher the prize of an Alpine Formula Three car. Cevert duly qualified for the final race and won.

His first season in F3, at the wheel of his prize Alpine, did not go well. He lacked the funds and experience to properly set up and maintain his car.[citation needed] After finding sponsorship for the 1968 season, Cevert traded in his Alpine for a more competitive Tecno car. With his new mount Cevert finally started to win races, and by the end of the season he was French Formula 3 Champion, just ahead of Jean-Pierre Jabouille.

After winning the French Formula 3 Championship, Cevert joined the works Tecno Formula Two team in 1969, and finished third overall, as well as driving in the F2 class of the 1969 German Grand Prix. At the time, Formula Two was an ideal training ground for ambitious drivers, as many top Grand Prix drivers also competed in the F2 class, when their Formula One schedules permitted. When Jackie Stewart had a hard time getting around Cevert in an F2 race at Crystal Palace the same year, Stewart told his team manager Ken Tyrrell to keep an eye on the young Frenchman. This personal recommendation was to pay off in 1970, as when Tyrrell needed a new driver at short notice Stewart's recommendation was still in his mind. Tyrrell later commented on the reason for Cevert's appointment to the Formula One team that "everybody said it was (French oil company and Tyrrell sponsor) Elf, but it was really what Jackie said about him."[3]

Formula One

Cevert at the 1971 Rothmans World Championship Victory Race
When Johnny Servoz-Gavin suddenly retired from the Tyrrell Formula One team three races into the 1970 season, Tyrrell called upon Cevert to be his number two driver, alongside defending World Champion Stewart. Over the next four seasons, Cevert became the veteran Stewart's devoted protégé. After making his debut at the Dutch Grand Prix at Zandvoort in Tyrrell's second customer March-Ford, he increased his pace and closed the gap to Stewart with virtually every race. He earned his first World Championship point by finishing sixth in the Italian Grand Prix at Monza.

In 1971, with the Tyrrell team now building their own cars, Cevert finished second in France and Germany, both times behind team leader Stewart. Then, in the season-ending United States Grand Prix at the newly extended Watkins Glen race course, the Frenchman earned his first and only Grand Prix win:

Having started from fifth spot, Cevert took the lead from Stewart on lap 14 as the Scot's tires began to go off in the 100° heat. At about half-distance, Cevert finally began to struggle with the same understeer that had plagued Stewart much earlier. Jacky Ickx was closing, and his Firestones were getting better as the race went on. On lap 43, Ickx set the fastest lap of the race, and the gap was down to 2.2 seconds. Then, on lap 49, the alternator on Ickx's Ferrari fell off, punching a hole in the gearbox and spilling oil all over the track! Denny Hulme's McLaren hit the oil and spun into the barrier, bending his front suspension. Hulme was standing beside the track when Cevert came by and also slid off and hit the barrier, but he kept going, now 29 seconds in the lead! Cevert coasted home, taking both hands off the wheel to wave as he crossed the line.[4]

Cevert became only the second Frenchman to win a Formula One World Championship Grand Prix (Maurice Trintignant won at Monaco in 1955 and 1958), and received 50,000 U.S. dollars as award. It was the high point of his career, helping him take third place in the 1971 Drivers' Championship behind Stewart and Ronnie Peterson.


François Cevert driving Matra 670 at the Nürburgring 1973
Great expectations for Cevert, Stewart and Tyrrell were not fulfilled in 1972, Cevert finished in the points only three times, with second places in Belgium and the USA, and a fourth at his home race in France at the Clermont-Ferrand circuit. One bright spot in a disappointing year for Cevert was his second-place finish at the 24 hours of Le Mans, driving a Matra-Simca 670 with New Zealand's Howden Ganley.

Death Edit
In 1973, the Tyrrell team was back on top in Formula One and Cevert showed he was capable of running with Stewart at almost every race. He finished second six times, three times behind Stewart, who acknowledged that at times the Frenchman had been a very "obedient" teammate. As Cevert began to draw even with Stewart's driving abilities, the Scot was secretly planning to retire after the last race of the season in the United States. For the 1974 season, Cevert would be Tyrrell's team leader.

At Watkins Glen, with Stewart having already clinched his third World Championship, Cevert was killed during Saturday morning qualifying, while battling for pole position with Ronnie Peterson. In the fast right-left uphill combination called "The Esses", Cevert's car was a little too far over towards the left side of the track, getting a bump from the kerbs.[5] This made it swerve towards the right-hand side of the track, where it touched the track's signature powder blue safety barriers causing it to spin and crash into the barriers on the other side of the track at a near 90° angle, uprooting and lifting the barrier. Cevert died instantly of massive injuries inflicted by the barrier.

Cevert had crashed violently in the uphill Esses heading onto the back of the circuit. Fighting the car as he went up the hill, he brushed the curb on the left, whipped across the track and hit the guardrail on the right. The car began to spin, and he swerved back across the track at 150 mph and hit the outside guardrail almost head-on, Stewart said.

Jackie Stewart was one of the last on the scene of Cevert's accident and said later "They [the marshals] had left him [in the car], because he was so clearly dead." Stewart immediately left the scene of the accident and returned to the pits. Because of Cevert's death, Tyrrell withdrew its entry for this GP, and Stewart did not run his final, and 100th race.

Cevert was 29 years and 224 days old. François Cevert is buried in the Cimetière de Vaudelnay in the village of Vaudelnay, Maine-et-Loire.

Cause of the accident analysed by Stewart Edit
When practice resumed, Stewart went out on the track in his car on a personal fact-finding mission. His conclusion was that his own preference was to take The Esses complex in fourth gear in the Tyrrell, hence he would be at the low end of the engine's rev range, making the car more tractable and less nervous (in exchange for a bit less throttle response). Cevert, however, preferred to use third gear and be at the top end of his engine's power range: it was always something of a compromise because of the need to accelerate through the combination of corners. Stewart noted that the Tyrrell always felt jumpy through this section of the Watkins Glen track owing to its short wheelbase; he felt that this was somewhat counteracted by driving in the higher gear even though this meant a time penalty if he got his line wrong through the corner. A film documentary of the time, shot minutes before the start of the fatal practice session, captures Stewart and Cevert in a spirited debate on exactly this point. Another accident occurred at the same circuit a year later in the 1974 USA Grand Prix when another young Formula One driver, Helmuth Koinigg, died when his car went straight into the barrier at turn 7.[6] As a response to Cevert's and Koinigg's accidents, a chicane was added in 1975 in order to slow the cars through the "Esses". The chicane was removed in 1985 after the track lost its Formula One race in 1981.[7]

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 18, 2018 3:08 pm
by OlaHansson
I also have built the 003, going to follow this one :th:

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 18, 2018 3:32 pm
by Twokidsnosleep
Very much following along :pop:

I read every word of that intro and knew nothing about it...just a smidge before my time
Interesting to say the least

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 18, 2018 3:46 pm
by Tay99
Thanks Scott.

Such a tragedy it was meant to be Jackie Stewart's last race, and I think francois was destined to be the next world champion.
The 70s was a bad decade for formula 1 with the amount of lives lost Jackie Stewart did a lot for the safety but got a lot of flack from the media at the time.
If you can find it the bbc did a thought provoking documentary about it. It's called f1 the killer years.

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 18, 2018 4:58 pm
by DrSprue
Wow awesome sprue layout and history! Im following along! :pop:

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 18, 2018 8:40 pm
by Tay99
Thanks everyone for taking a interest.
Made a start by making the rear wing and priming and painting the bodywork.

Image

Image

Then made up the engine and gearbox, and preped a few other parts ready for painting.

Image

Image

Image

Image

That's all for now thanks for looking.

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 18, 2018 10:46 pm
by Twokidsnosleep
So would you say the Ebbro kits are on par with the Tamiyas???
Look pretty similar

Re: Tyrell 002 Francois Cevert.

Posted: Mon Feb 19, 2018 7:23 am
by Kevthemodeller
I've read they're mate some rate them better than Tamiya. I've seen some cracking finished examples check this out http://www.scaleworks365.com/forums/top ... -ford-003/

Re: Tyrell 002 Francois Cevert.

Posted: Mon Feb 19, 2018 10:32 am
by Tay99
From what I’ve read a few Tamiya employees left to work for Ebrro, the fit and moldings are just as good, there is a slight issue with this build which I will highlight in my next update

Re: Tyrell 002 Francois Cevert.

Posted: Wed Feb 21, 2018 9:00 pm
by Tay99
Hi
Just a quick update, I've primed all the parts and have got the body painted with the zero paints Tyrrell blue.
I've also sprayed some of the parts with Alcald aluminuam.

Image

I've also removed the chrome from the parts with mr muscle oven cleaner and then sprayed them with black primer I will then
Spray the parts with gloss black ready for the Alcad chrome paint.

Image

While trawling the web for ref photos I came across this site some great ref photos and a fascinating story about how the car was designed
http://www.britishracecar.com/JohnDimme ... ll-004.htm

That's all for now.

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 25, 2018 5:30 pm
by Tay99
Next update.

Glossed black the chrome parts and sprayed with mr color super metallic chrome for a more realistic look.
Painted few other parts ready for assembly.

Image

Next up start to build the front end

Image

Top half of the the cockpit with pedals installed

Image

Image

Here's the engine block made up and the cam covers detailed.

Image


That's all for now thanks for looking.

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 25, 2018 5:33 pm
by Twokidsnosleep
Nicely done
How much engine detail you going to do???
I have been trying to get as many photos on the Cosworth engine to do a decent job of some of the plumbing...it isn’t easy
Streatched thin clear sprue was best for me with the injector lines...can leave clear or paint if desired

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 25, 2018 6:12 pm
by Tay99
Hi Scott have a look at the link below it will give you a close up,look at Tyrrell with the cosworth in the back.

http://www.britishracecar.com/JohnDimmer-Tyrrell-004.

I have some model factory hiro small clear yellow tubeing for the fuel lines.
On the other Tyrrell I built I cut off the small peg on the injectors and drilled a hole for the tubing to go into and stuck them with some CA glue.

Re: Tyrell 002 Francois Cevert.

Posted: Sun Feb 25, 2018 9:01 pm
by OlaHansson
Tay99 wrote: Sun Feb 25, 2018 5:30 pm Next update.

Glossed black the chrome parts and sprayed with mr color super metallic chrome for a more realistic look.
Painted few other parts ready for assembly.
Looks great!
Have to try that :)

Re: Tyrell 002 Francois Cevert.

Posted: Mon Feb 26, 2018 10:21 am
by demarcation
Nice work so far!!

Re: Tyrell 002 Francois Cevert.

Posted: Mon Feb 26, 2018 10:39 am
by Kevthemodeller
It's looking really good mate :th:

These kits really do look good, don't they I think I need to check them ou t........oh no more additions to the stash :crazy: :whistle:

Re: Tyrell 002 Francois Cevert.

Posted: Mon Feb 26, 2018 5:10 pm
by Tomcat64
Great work so far mate.

I love the look of Formula One cars from this era - leaving aside the safety issues it was a great period of creativity and the cars looked and sounded different from each other.

Re: Tyrell 002 Francois Cevert.

Posted: Thu Mar 01, 2018 4:01 pm
by Tay99
Thanks for all the comments guys.

Next update, I've been working on the wiring and fuel lines the last week.
The fuel lines are from model factory hiro and the intake trumpets are by Ejan.

Image

Image

Image

Image

Image

Re: Tyrell 002 Francois Cevert.

Posted: Thu Mar 01, 2018 4:05 pm
by Twokidsnosleep
Oh man, that is a beautifully detailed engine!!!
The injector lines look sweet
I think I will go melt my Lotus engine down now :oops:

Re: Tyrell 002 Francois Cevert.

Posted: Fri Mar 02, 2018 11:57 am
by Tay99
Thanks Scott.

Next update bit more work on the engine and gearbox, added AN fitting to the fuel meter on the end of the cam cover and to the oil coolers.
Fitted the rear suspension and drive shafts
Body work added the decals,
Dressed up the dash board with some toggle switches.
PE rivets added to the air scoop.

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

That's all for now thanks for looking.

Re: Tyrell 002 Francois Cevert.

Posted: Fri Mar 02, 2018 4:03 pm
by Twokidsnosleep
Lovely work, all so crisp and clean
I really like the radiator connectors, are they metal???
Those detail parts are a good demonstration why MFH has such a good reputation :thumb2:

Re: Tyrell 002 Francois Cevert.

Posted: Fri Mar 02, 2018 4:11 pm
by Tay99
Twokidsnosleep wrote: Fri Mar 02, 2018 4:03 pm Lovely work, all so crisp and clean
I really like the radiator connectors, are they metal???
Those detail parts are a good demonstration why MFH has such a good reputation :thumb2:
Thanks Scott.

The connectors are from hobby design. RB motion also do them.

Re: Tyrell 002 Francois Cevert.

Posted: Sat Mar 03, 2018 5:21 pm
by Tay99
Hi all next update finaly got the 2k on first thing this morning. and properly did my best job so far with it.
Got the rest of the front suspension done.
Made up the seat belts.
Also found some pictures of Francois in action and of the car in the pits.


Image

Image

Image

Image

Image

Image

Image

Image

Image

That's all for now and thanks for looking.

Re: Tyrell 002 Francois Cevert.

Posted: Sat Mar 03, 2018 7:10 pm
by OlaHansson
Great work!!